CHOISISSEZ L'APPAREIL POUR VOTRE BUT

Avoir des questions?
Appelez, notre responsable
est toujours en contact:

Sélection d'un appareil pour mesurer la résistance dans les équipements électriques

L'un des moyens les plus courants et les plus simples d'évaluer l'état des nœuds des disjoncteurs, sectionneurs et séparateurs haute tension, les courts-circuits, les conducteurs, les transformateurs, les machines électriques et les équipements électriques similaires consiste à mesurer leur résistance électrique au courant continu.

SKB EP est engagée dans le développement et la production de dispositifs pour la surveillance et le diagnostic des équipements de commutation haute tension. Nos assortiment de SKB EP comprend les appareils mobiles de haute précision pour la mesure de la résistance électrique:

  • microohmmètres (MIKO-1MIKO-10MIKO-21)) pour mesurer les résistances transitoires des contacts des appareils de commutation et des connexions de contact des conducteurs de courant;
  • milliohmmètres (MIKO-7М(А)МIKO-8М(А)MIKО-9А) pour mesurer les résistances actives des circuits à haute inductance (transformateurs, moteurs électriques, électroaimants, etc.);
  • micromillikiloohmmeter (МIKO-2.3), qui couvre les tâches des appareils précédents, ainsi que la mesure de la température de différents milieux.

L'équipement SKB EP prend en compte les particularités des processus physiques dans les équipements électriques et les exigences techniques pour assurer l'exactitude des mesures et le travail pratique de ses utilisateurs, nous vous suggérons donc de considérer les critères et paramètres qui sont pris en compte dans les appareils SKB EP, ainsi que ce à quoi vous devez faire attention lors du choix. d'un type particulier d'appareil:

Pour les microohmmètres (appareils de mesure de la résistance de contact), la principale exigence est de fournir un courant suffisamment important à travers la résistance de contact. Le film d'oxyde et les inclusions de contact non métalliques provoquent une dépendance non linéaire de la résistance transitoire sur le courant circulant. Par conséquent, afin d'obtenir des valeurs fiables, il est recommandé d'effectuer des mesures à des courants suffisamment élevés à travers la résistance de contact, ce qui est reflété, par exemple, dans les normes CEI 56 (I≥50A) et ANSIC 37.09 (I≥100A).

Les disjoncteurs de réservoir haute tension dans leur conception ont des transformateurs de courant intégrés et la plupart des instruments de mesure de la résistance dans de tels objets ne conviennent pas, car Le courant de mesure du microohmmètre doit circuler à travers le circuit de manière stable et pendant une durée suffisante, et le microohmmètre lui-même doit fonctionner de manière stable dans des conditions de champs électromagnétiques puissants.

Pour les y (dispositifs de mesure de la résistance CC des circuits à inductance élevée), les principales exigences sont d'assurer un courant stable dans l'enroulement et de limiter la force électromagnétique de l'auto-induction lorsqu'il est éteint ou lorsque le circuit de courant est coupé. Les circuits électriques tels que l'enroulement primaire d'un transformateur puissant ont une inductance importante. Par conséquent, le courant y est établi assez lentement. Et puisque selon RD 34.45-51.300-97, des mesures de résistance doivent être effectuées pour toutes les branches, c'est-à-dire dans toutes les positions des appareils de commutation, et pour tous les enroulements, le temps total nécessaire est important.

The accuracy requirements for milliometers can determin on the basis of the tolerance on the deviation of the resistance of the transformer windings. They can be both between themselves and from the passport values. Since this tolerance should not exceed 2%, the maximum basic measurement inaccuracy should not exceed (0.5 ... 1)%.

Instruments for measuring the resistances of shunting resistors of high-voltage circuit breakers can call kiloohmmeters. Since the upper limit of the range of these resistances reaches 100 kOhm (the shunt resistance of each chamber of the MKP-220 circuit breaker). A feature of this type of measurement is the presence of induced voltage at a frequency of 50 Hz on the measured resistors. Induced voltage occurs when capacitive current flows from lines under high voltage through a resistor to ground. The size of the induced voltage determines by the line voltage level, design, location and resistance value of the resistor, atmospheric conditions and can reach several kilovolts.

When measuring resistance, the interference current with a frequency of 50 Hz can be several orders of size higher than the measuring current of the instrument. During resistance measurement, the interference current with a frequency of 50 Hz can be several orders of size higher than the measuring current of the instrument. Due to the difficulties in ensuring the required level of noise suppression (about 120 dB) there are very few special instruments of this kind. At the same time, the use of kilo ohm meters makes it possible to measure the resistance of resistors under conditions of high noise on electrical equipment without extra labor costs.

As follows from the foregoing, we need several specialized instruments to measure all types of electrical circuit resistances, which is not always convenient. The provision of all these functions with one instrument is most preferable. Especially since the cost of a set of instruments with the same characteristics will be higher than the cost of one universal device. Back in 2008, SKB EP Company launched the МIKO-2.3 universal instrument. Device has since taken a stable position in the market. МIKO-2.3 also includes the fourth type — a thermometer (immersion type) for measuring various temperatures liquids, including oil.

Mode  Range (R)  Current (I) Accuracy (δR
Microohmmeter   0,1 μΩ ÷ 0,1 Ω
10 ÷ 1 000 А
±0,2%
Milliometer 100 μΩ ÷ 1 kΩ 0,5 ÷ 5 А
±0,2%
Kilohmmeter 0,1 kΩ ÷ 300 kΩ
- ±0,5 %
Thermometer -20 °C to +120 °C
- -
The mass of the device without cables - 2.7 kg
The mass of the device complete with cables - 9.5 kg

The use of modern components, special measurement algorithms and a thoughtful original design made it possible to increase the current in the microohmmeter mode to 1000 A. But to maximized battery life in the microohmmeter mode the measurement current is adjustable. Thanks to this mode, one battery charge is enough for 40 transition resistance measurements. So, one battery charge is enough for 40 transition resistance measurements. Autonomous power supply from the built-in battery and low weight of the instrument (2.7 kg) make it easy to climb switches and transformers with it. And the length and weight of the connecting cables can reduce.

In millimeter mode, the measuring current range of МIKO-2.3 coincides with the current range of many milliometers (0.5 ÷ 5A). Plus МIKO-2.3 have special technique is developed by SKB EP to determine the additional inaccuracy caused by non-zero current instability. Tests by the method revealed the maximum additional inaccuracy which does not exceeding 0.1% in the range of inductance of the circuit (0.01 ... 15) GN.

After measuring the active resistances of the windings, another cable with a temperature sensor can connect to МIKO-2.3 and the instrument will switch to digital thermometer mode. In this mode, the actual temperatures of the windings measure to convert their resistances to the rated temperature.

The safety of work when measuring resistance with a large induced voltage in kilometer mode ensure by the usual organizational measures. They provide for in the design and circuitry of МIKO-2.3. They are clamps in cable grips, voltage suppressor in the input circuit, etc.

A serious drawback of most universal instruments is the increased complexity of use. It arises due to the fact that the instrument must have all the controls and inscriptions necessary to perform all the functions provided. In МIKO-2.3, technical solutions a use to avoid the reverse side of the advantages of universality:

Firstly, it provides automatic inclusion of a certain type of measurement when connecting the input cable. As well as the conclusion of the relevant information on the display.

Secondly, all functioning processes are automating. For example, these are processes such as compensation of the initial level and thermal emf, determining the parameters of an object, selecting a measurement range and operating current, assessing the level of interference and establishing the necessary degree of filtration, and many others.

Thirdly, a special program monitors at what step is the implementation of each type of measurement. Then, a message appears on the display. And after connecting the cables to the object, it controls the integrity of the contact via potential and current wires. In case of violation, instrument issues a warning.

Universal МIKO-2.3 allows you to get by with the only instrument for all the tasks at hand, instead of three or four devices. Moreover, it has a record high current in the microohmmeter mode with a record low weight. All these advantages are especially relevant for installation and repair organizations. Such organizations, by the nature of their work, are forced to move large masses of instruments, appliances and tools over long distances.

Nous utilisons des cookies. Encontinuant à utiliser le site, vous acceptez le traitement de vos données personnelles à l'aide de ces fichiers et de la politique de confidentialité.